Skip to main content Skip to search Skip to main navigation

Water mattresses for softside and hardside

The water mattress – also called water core or water bag – is the heart of every waterbed and at the same time the only part that really wears out over the years. The frame, heater and base usually last much longer. A leaking or worn-out core is therefore no reason to buy a complete bed. You will find replacement cores for almost every system in our category Water mattresses, water cores and water bags.

Which core belongs in your bed depends mainly on the type of construction: softside beds and hardside beds need differently cut mattresses. On this page you will find the differences, the dimensions that matter and the details that allow us to find the right water mattress for you quickly.

Recognising softside or hardside

If you no longer know which type you have at home, a look at the edge of the bed helps. You do not need to drain the water or remove the cover for this.

Features of a softside bed

The edge of the bed gives way when you press on it, because there is a foam frame under the cover. From the outside the bed looks like an ordinary upholstered bed, and you can sit on the edge. The cover can usually be opened with an all-round zip. In Germany this is by far the most common type.

Features of a hardside bed

The edge of the bed is hard – underneath is a wooden frame that holds the water. You cannot sit on this edge. The water core lies freely in the wooden frame, with only a thin cover on top. Hardside beds often date from the 1980s and 1990s and follow US sizes.

Water mattresses for softside beds

In a softside bed, the water core lies in a foam tub. So that it sits neatly against the frame and the lying surface stays level right to the edge, these cores are cut to the inner dimensions of the foam frame – with different edge shapes depending on the manufacturer:

Straight cut: the side wall is vertical and the core fills the frame in a rectangle.

Sloped cut: the side wall narrows towards the bottom and so follows the slope of the foam frame.

Concave: the side wall curves inwards, and the foam frame fits into this curve.

The edge shape is not a question of comfort but of fit. A straight-cut core in a frame designed for a concave edge pushes the foam outwards and makes the edge of the bed feel unsteady. The easiest way to recognise the shape is from the label on the old core or from a photo of the drained mattress. All softside water mattresses – straight, sloped and concave – can be found in the category Softside replacement mattresses.

Water mattresses for hardside beds

In a hardside bed, the wooden frame provides the support. The core therefore needs straight, vertical walls and is simply made to the clear inner dimensions of the frame. The classic US formats are common, such as Super Single at about 122 x 213 cm, Queen at about 152 x 203 cm and King at about 183 x 203 cm. The core height is usually 20 to 23 centimetres.

Even though many of these beds have not been built for years, we still make matching cores, in special sizes too on request. An overview of the available sizes can be found in the category Hardside water mattresses.

Mono or Dual

Mono, also called Uno: one large water chamber across the whole bed – even in a double bed. Both sides therefore have the same level of stabilisation and the same amount of water.

Dual: two separate water chambers lying side by side in the double bed, with a thermal divider between them. Each side can be filled and stabilised individually – the usual choice for couples with different weights or preferences.

With a dual bed you can reorder a single side. Pay attention to left or right – this always refers to the view of the bed when you are standing in front of it.

There are no other layouts for the water mattress. The term split does not refer to the water core but to the construction of the foam surround – see the next section.

Surround: Classic, Basic or Split

In a softside waterbed, the water core lies in a foam surround that runs all the way round the mattress. How this surround is built helps determine how the bed feels and how it looks.

Classic and Basic: the softside edge is made in one piece on the outside – continuously from the base board to the top.

Split: here the edge is divided on the outside. At the top is a foam edge of about 10 to 12 centimetres that slopes inwards into the bed, and below it there is usually a profile.

The split construction has several advantages: the upper foam edge is easier to cover with a fitted sheet. It gives inwards when you lie down, creating less tension under the body so that you sink in more evenly. And the lower part, which has no load-bearing function, can be covered on the outside – with fabric or imitation leather that can be wiped clean. This lets you match the colour of the bed edge to the headboard or the other furniture in the room.

The four details we need

1. Type: softside or hardside.

2. Inner dimensions: length and width of the frame – for softside measured inside the foam frame, for hardside inside the wood.

3. Frame height: 15, 17, 20 or 23 centimetres are common.

4. Layout and stabilisation: mono or dual, and how strongly stabilised the previous core was.

If you know the brand of your bed, please tell us straight away – that is the quickest way to find the right mattress. A photo of the label on the old core also helps: with most manufacturers it shows the size, stabilisation level and year of manufacture. For individual manufacturers we have separate pages with details on dimensions and types – for example Bodytone waterbeds and TTI waterbeds with Stretch Top and Royal Sleepline.

Material and service life

Our water mattresses are made in the EU from Mesamoll 2 vinyl, a phthalate-free plasticiser system from Bayer AG. We give a 10-year guarantee on the cores.

How long a core lasts depends mainly on care: add conditioner once or twice a year, do not overheat the bed permanently and bleed it once a year. With that, ten to fifteen years is realistic.

A quick call is worthwhile – especially with older beds.

Whether a water mattress really fits depends on details you have to check on the bed itself: edge shape, inner dimensions, the stabilisation you want and the corner where the filling valve sits. Two minutes on the phone, ideally with a photo, save you the hassle of a return.

It is easiest if the brand of your bed is known – then the right water mattress is usually clear straight away. With older beds, however, the manufacturer often can no longer be traced: the label is missing, the documents are gone or the company no longer exists. That is no obstacle either. On the phone we ask about a few features – how the individual parts of the bed are built, what colour and embossing the mattress has, how the edge is cut. With decades of experience of the common systems, the brand can be identified this way in the vast majority of cases.

Phone: +49 6887 912 9180 – Monday to Saturday, 8 am to 8 pm (advice in German) · Email: info@betten-conrad.de

Waterbed brands from A to Z

Do you know the brand of your bed? Then that is the quickest way to the right water mattress. For each of these brands we have a separate guide page with background, special features and the matching replacement water mattresses:

Abbco · AKVA · Alivio · American National · Aqua Comfort · Aqua Dynamic · Atlantis · Baltimore · Betttotal · Blue Beds · Bodyform · Bodyline · Bodytone · Cascade · Dragon · ESP · Estrella · Ettkus · EWP · Halcyon · ITW · Kallisto · Kuss · Land and Sky · Luna Live · Luna Rest · Lunar · Mastersleep · Mermaid · Poseidon · Profile · Profine · RWM · Schlaraffia · Silvaline · Starlight · Sterling · Strata · Tasso · TTI · Wacore · Wasserbett24 · Waterdream · Wellness Company · Wigwam · Winkle · Wohnform

Your brand is not listed or you no longer know it? Call us – from the construction, edge and mattress we can identify most beds even without a label.

Frequently asked questions

Will a softside mattress fit a hardside bed?

No. The core for a softside bed is cut to the foam frame and, depending on the model, has sloped or curved edges. In the wooden frame of a hardside bed it would form folds at the sides and make the lying surface uneven.

Do I have to replace both cores in a dual bed?

Technically no – a single side can be replaced. But if the second core is of a similar age, replacing both together is usually worthwhile, because both sides will then feel equally soft and you only have the effort once.

Is a special size possible?

Yes. We have cores made to measure, including for old or discontinued models. Please contact us by phone with the inner dimensions of your frame.

Does the position of the filling valve matter?

Yes. The valve should be in the same place as before so that you can reach it through the opening in the cover. Before draining, note which corner it is in.

Water mattress as a continuous Uno core for softside waterbeds

Dual water mattress with two separate water cores and a thermal divider